Tagged: 

Viewing 15 posts - 1 through 15 (of 23 total)
  • Author
    Posts
  • #43801
    libjon09
    Participant

    I can not get into the main page of fluxion when I run (bash fluxion.sh) I doubt something to do with the pyrit also coz it shows Not Installed. I did re-installed the fluxion program.

    Below the screen copy after after I run fluxion

    aircrack-ng…..OK!

    aireplay-ng…..OK!

    airmon-ng…….OK!

    airodump-ng…..OK!

    awk………….OK!

    curl…………OK!

    dhcpd………..OK!

    hostapd………OK!

    iwconfig……..OK!

    lighttpd……..OK!

    macchanger……OK!

    mdk3…………OK!

    nmap…………OK!

    php-cgi………OK!

    pyrit………..Not installed

    python……….OK!

    unzip………..OK!

    xterm………..OK!

    openssl………OK!

    rfkill……….OK!

    strings………OK!

    fuser………..OK!

    root@kali:/opt/fluxion# bash fluxion.sh

    #43821
    Diego PérezDiego Pérez
    Moderator

    Hi!
    Try using this version instead:
    https://github.com/FluxionNetwork/fluxion

    Let me know how it goes!
    Diego

    #43840
    libjon09
    Participant

    Pyrit …….. not installed again same issue. I downloded the version that you sent to me.

    #43841
    libjon09
    Participant

    But i want to use fluxion 2.0 not fluxion 6.9 because it has more issue than fluxion 2.0

    #43842
    libjon09
    Participant

    In fluxion 2.0 i have pyrit …not installed problem but i want to use fluxion 2 as zaid told on his lectures

    In fluxion 6.9 , i have “unable to start captive portal interface ,returning “ problem.

    #43865
    Diego PérezDiego Pérez
    Moderator

    Hi!
    If you want to use fluxion 2 then follow these steps:
    https://github.com/hacker3983/how-to-install-pyrit-on-kali-linux-2020.1a

    Just don run apt-get upgrade.

    Can you tell me the exact model of your adapter?(brand and model)

    Greetings!
    Diego

    #43873
    libjon09
    Participant

    Yes , this is wifi adapter
    Chipset
    Realtek RTL8812AU
    WiFi Standards
    IEEE 802.11ac/a/b/g/n
    WiFi Frequency
    Dual Band 2.4GHz or 5GHz
    Antenna Connector
    RP-SMA female x 2
    Antenna Type
    2.4G/5GHz Dual-Band 5dBi dipole antenna
    Wireless Performance
    802.11a: up to 54Mbps
    802.11b: up to 11Mbps
    802.11g: up to 54Mbps
    802.11n: up to 300Mbps
    802.11ac: up to 867Mbps
    Wireless Security
    64/128 bit WEP,WPA/WPA2,WPA-PSK/WPA2-PSK,WPS
    Interface
    USB 3.0

    #43882
    libjon09
    Participant

    alfa AWUS036ACH is the name

    #43884
    libjon09
    Participant

    it is fixed , pyrit … ok . but there is another issue : fatal: destination path ‘revolver’ already exists and is not an empty directory.

    chmod: cannot access ‘revolver/revolver’: No such file or directory

    mv: cannot stat ‘revolver/revolver’: No such file or directory

    what to do with this?

    #43885
    libjon09
    Participant

    it is fixed also the revolver but the next issue is that i chose all channels, then wifi monitor is not showing me any results.

    #43886
    libjon09
    Participant

    sometimes wifi monitort dont work , sometimes it says Error: your wireless card isn’t supported Do you want exit? [Yes / No]:

    #43924
    Diego PérezDiego Pérez
    Moderator

    Hi!
    Can you share some screenshots of the settings used in fluxion? Can you share the results of ifconfig BEFORE running the attack?

    Thanks!
    Diego

    #43967
    libjon09
    Participant

    where can i upload the screenshots cause here i cannot upload them?
    And where can i find fluxion settings ? what is the sintax i mean.

    sometimes wifi monitor in fluxion is empyt and sometimes there is said that there is ” error your wireless card is not supported”

    #43985
    Diego PérezDiego Pérez
    Moderator

    Hi!
    You can upload the images to any image hosting service, then share the link here. By fluxion settings I mean each you are selecting when trying to launch the attack.
    Let me know.
    Diego

    #44025
    libjon09
    Participant

    https://www.sendspace.com/file/r7q4de

    FROM capture 1 to 7 is the first try
    then after first try, a wifi mon0 is showed in ifconfig , then when i try for the second type it is showed to choose a wifi interface from mon0 or wlan0 , then it shows the error. you can see the screenshots here

Viewing 15 posts - 1 through 15 (of 23 total)
  • You must be logged in to reply to this topic.
Privacy Overview
ZSecurity logo featuring a stylized red letter Z

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.

Strictly Necessary Cookies

Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.

3rd Party Cookies

This website uses Google Analytics and Linkedin to collect anonymous information such as the number of visitors to the site, and the most popular pages.

Keeping these cookies enabled helps us to improve our website.