- This topic has 7 replies, 2 voices, and was last updated 4 years, 7 months ago by
.
- Posts
I buy a antena for linux, installed drivers.
run linux and vm didn’t detect the antena google up and I installed another drivers for linux wireless.
when I run iwconfig in terminal I got two wlan.
Tried toiwconfig
lo no wireless extensions.
wlan0 IEEE 802.11 ESSID:off/any
Mode: Managed Access Point: Not -Associated Tx-Power=20 dBm
Fragment thr:off RTS thr:off Retry short limit: 7
Encryption key: off
Power Management : on
eth0 no wireless extensions.
hwsim0 no wireless extensions.
wlan1 IEEE 802.11 ESSID:off/any
Mode:Managed Access Point: Not -Associated Tx-Power=20 dBm
Fragment thr:off RTS thr:off Retry short limit: 7
Encryption key: off
Power Management : onDid you add the card to usb list like shown in lecture 11? If you did, then make sure that you don’t physically connect the card to the computer until Kali is fully booted, connect the card, then go to the devices menu (beside the file menu) >> USB >> Click your device.
If you’ve done all of the above then can you tell me the exact model of your wireless adapter please?
Also can you show me the result of ifconfig&lsusb&airmon-ng?Thank you.
Mac OS 10.15.4
Hi Vashisht i restored my vm snapshot when I run my vm,went to deices>usb>Realtek usb3.0 802.011ac 1200m
noticed my Mac has a usb icon on the top left bar,so when I run vm it has an red x on usb icon.
should I install linux drivers for the usb antena?[SOLVED]
UPDATE:
root@kali:~# lsusb (to check if its reconigzed by USB ports)
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 0bda:b812 Realtek Semiconductor Corp. USB3.0 802.11ac 1200M Adapter
Bus 001 Device 002: ID 80ee:0021 VirtualBox USB Tablet
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@kali:~# usb-devices (info about devices)T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev=05.04
S: Manufacturer=Linux 5.4.0-kali3-amd64 xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:00:0c.0
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hubT: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=80ee ProdID=0021 Rev=01.00
S: Manufacturer=VirtualBox
S: Product=USB Tablet
C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhidT: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=b812 Rev=02.10
~S: Manufacturer=Realtek~
~S: Product=USB3.0 802.11ac 1200M Adapter~
S: SerialNumber=123456
C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 5 Cls=ff(vend.) Sub=ff Prot=ff~~~ Driver=(none)~~~~T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=5000 MxCh= 6
D: Ver= 3.00 Cls=09(hub ) Sub=00 Prot=03 MxPS= 9 #Cfgs= 1
P: Vendor=1d6b ProdID=0003 Rev=05.04
S: Manufacturer=Linux 5.4.0-kali3-amd64 xhci-hcd
S: Product=xHCI Host Controller
S: SerialNumber=0000:00:0c.0
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#=0x0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hubSearched for chipset of antena and installed drivers:
#Followed this steps:
cd rtl88x2BU_WiFi_linux_v5.3.1_27678.20180430_COEX20180427-5959
VER=$(sed -n ‘s/\PACKAGE_VERSION=”\(.*\)”/\1/p’ dkms.conf)
sudo rsync -rvhP ./ /usr/src/rtl88x2bu-${VER}
sudo dkms add -m rtl88x2bu -v ${VER}
sudo dkms build -m rtl88x2bu -v ${VER}
sudo dkms install -m rtl88x2bu -v ${VER}
sudo modprobe 88x2bu
- You must be logged in to reply to this topic.
